Tech Mode

• Press to view HP Part No. of eprom

• Press to view software ID

• Press to view software version

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

Press any of the control buttons to test operation. You should hear a beep, and the LED should light and/or a display.

Press any of the product buttons and all the LEDs and display segments should light.

Press any of the product buttons to view a different segment of the display characters.

Press any of the product buttons numerous times to view all segments of each digit across the displays.

Press any of the product buttons numerous times to view all decimal points across the displays.

Press any of the product buttons numerous times to view each LED across the control panel.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

H = HIGH LIMIT - If “H” is present, the high limit is good.

If “-” shows then the high limit is tripped out (overheated) ordisconnected.

D = DRAIN SWITCH - If “D” is present, the drain handle (when applicable) is closed. If “-” shows then the drain is open or the switch is faulty.

E = ELEMENT SWITCH - If “E” is present, the element switch is good. If “-” shows in the display, the element is in the upright position, or the switch is faulty.

Press the right arrow button and an underscore (“_”) indicates the input is not presently detected. A Checkmark (“√” ) indicates the signal is detecting a normal input. A blinking (“X”) indicates the signal is presently detected, but is detected as a half-wave (partially failed) input.

The H, D, E signals above are wired in series. The first signal missing out of this sequence l generally causes all signals to the right of it to be missing as well.

An “AIF √ ” means normal communications between the AIF PCB and the control PCB. “AIF X” means a problem with the communications between the PCBs.

Press the Down arrow button and “FILR IN” and “USE BY 1(ex)” displays. These displays shows which controls are using the filtering system.

“USE BY 0” = not in use

“USE BY 7” = used by AIF

“USE BY 1 to 5” = used by control PCB

Press the Down arrow button and “CPU POSN” and “1 OF 3(ex)” displays. These displays shows which controls are plugged into which port on the AIF board.

For example, the left control should be plugged into port 1, and on a 3 control fryer, shows “1 OF 3” on the display.

If the right control is unplugged, then the left control would show

“1 OF 2” instead of “1 OF 3”.

Press the Down arrow button and “INP E_P_” and “JL_R_DT_” displays.

AIF Board Inputs:

E = Stop button E* = E-Stop pressed.

P = Drain Pan M* = drain pan is missing.

JL = JIB J* = JIB oil level is low.

R = RTI R* = RTI System Detected

DT = RTI Discard Tank DT* = tank full

Press the Down arrow button and “OUT F_J_” and “N_DI_oJF_” displays.

AIF Board Outputs:

Current outputs status from AIF board.

F = Filter Pump. (F* = Filter pump is on)

J = JIB Pump. (J* = JIB pump is on)

N = New Oil Pump. (N* = RTI new oil pump on)

DI = Discard Valve. (DIo = RTI disc. valve open/DIc=closed)

JF = JIB Fill Valve. (JFo = RTI JIB fill valve open/

JFc=closed)

Press the Down arrow button and “REQ F_J_” and “N_DI_oJF_” displays.

AIF Board Outputs Requested by the Control Board:

Current outputs status from AIF board.

F = Filter Pump. (F* = Filter pump is on)

J = JIB Pump. (J* = JIB pump is on)

N = New Oil Pump. (N* = RTI new oil pump on)

DI = Discard Valve. (DIo = RTI disc. valve open/

DIc=closed))

JF = JIB Fill Valve. (JFo = RTI JIB fill valve open/

JFc=closed)

S = SAFETY CONTACTOR - Press product button 6 safety (primary) contactor on full or right split vat.

Press product button 1 to turn off and on the safety (primary contactor on left split vat.

H = HEAT CONTACTOR - Press product button 7 to turn off and on the heat contactor on full or right split vat.

Press product button 2 to turn off and on the heat contactor on left split vat.

Press √ button and “VALVES” “DcRc” displays.

Press product button 6 to open and close the drain valves on full vat or right split vat.

Press product button 1 to open and close the drain valves on left split vat.

Press product button 7 to open and close the return valves on full vat or right split vat.

Press product button 2 to open and close the return valves on left split vat.

“DcRc” means valves are closed, “DoRo” means valves are open.

(Driven by the control board)

Press the Down arrow button and “DISCARDc” and “JIBFILLc” displays. (Driven by the AIF board)

Press product button 1 to open and close the RTI discard valve (display shows “DISCARDo” when open)

Press product button 2 to open and close the RTI JIB fill valve (display shows “JIBFILLo” when open)

Prior to energizing any pump, open a return, discard, or JIBFill valve.

Press the Down arrow button and “PUMP FP_” and “JP_ NP_” displays. (Driven by the AIF board)

Press product button 1 to turn off and on the filter pump (display shows “FP*” when on)

Press product button 2 to turn off and on the JIB pump (display shows “JP*” when on)

Press product button 3 to turn off and on the RTI new oil pump (display shows “NP*” when on)

Press the Down arrow button and “LIGHTS” and “FLT_ JLO_” displays. (Driven by the AIF board)

Press product button 1 to turn off and on the FILTER light (display shows “FLT*” when on)

Press product button 2 to turn off and on the JIB LOW light (display shows “JLO*” when on)

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.

For more information, contact Henny Penny service at +1-937-456-8405 or +1-800-417-8405.