OFE 51X Software with Connectivity

NOTE: Both software and procedure applies to both General Market F5 and McDonald's LOV3.

NOTICE

Only install this software on units built with connectivity hardware (units that DO have a Wi-Fi enabled dongle).

This includes:

All fryers manufactured with serial number: LC2602026 and after.

Installing an incompatible software version will permanently disable the control. No corrective action is available and replacing the control will be required.

How to visually determine if the fryer has connectivity hardware:

HENNYLINK Label

Figure 1

Look for the HENNYLINK label, shown in figure 1, located below the power switch on the left side of the fryer. The presence of this label indicates that the fryer is equipped with connectivity hardware.

Wi-Fi Enabled Dongle

Figure 2

Fryers manufactured after LC2602026 include connectivity hardware. Lower the far-left control of the fryer to verify if connectivity hardware is present. Connected units include the hardware identified in red in figure 2.

NOTE: Connectivity field test fryers that are in the field are not compatible with this software version. These fryers have serial numbers prior to LC2602026 but run on version 2.X.X. Please reach out to Henny Penny technical support if you need further assistance with replacing or updating a control on these fryers.

IMPORTANT: Do not perform this software update on F5 and LOV3 fryers which DO NOT include connectivity. Please visit Software: Non-Connectivity to find software updates for fryers that DO NOT include connectivity.

Please refer to the Software Guidance Bulletin and Memo for more information. If you need more guidance on which software to install, reach out to Henny Penny technical support.

Download this software only on a computer. Mobile device downloads may corrupt the file.

Version	Issues Fixed	Date Released	Click to Download
2.6.0	Software Update Release (RED Compliance Including South America) 2.6.0 started production on fryers starting with Serial Number: LC2608025 Software Versions Included with 2.6.0 package: • OMS: Version 1.2.0 • PMU: Version 1.1.0 Important Update Information! Fryers currently running Map UI Version 2.1.93 require this software package to be installed twice. This is required due to a security requirement that changes the update folder structure. This download file contains both updates: 1. First installation: Updates the fryer from Version 2.1.93 to Version 2.1.98 2. Second installation: Updates the fryer from Version 2.1.98 (or later) to Version 2.6.0 Installation Requirements Current Fryer Version Number of Installations Required 2.1.93 - Install the software package twice 2.1.98 or later - Install the software package once Verify the Current Software Version Before updating, check the fryer's current software version on the touch screen: Settings → Information → About This Fryer → More Information Reminder If the fryer is running Version 2.1.93, complete the normal software update procedure two times using the same software package to ensure the fryer is fully updated to Version 2.6.0.	08/05/2026	Download
2.1.98	Released RED compliance certification enabling global connectivity outside of South America.	04/10/2026	N/A

Version

Issues Fixed

Date Released

Click to Download

2.6.0

Software Update Release (RED Compliance Including South America)

2.6.0 started production on fryers starting with Serial Number: LC2608025

Software Versions Included with 2.6.0 package:

• OMS: Version 1.2.0

• PMU: Version 1.1.0

Important Update Information!

Fryers currently running Map UI Version 2.1.93 require this software package to be installed twice.

This is required due to a security requirement that changes the update folder structure.

This download file contains both updates:

1. First installation: Updates the fryer from Version 2.1.93 to Version 2.1.98

2. Second installation: Updates the fryer from Version 2.1.98 (or later) to Version 2.6.0

Installation Requirements

Current Fryer Version Number of Installations Required

2.1.93 - Install the software package twice

2.1.98 or later - Install the software package once

Verify the Current Software Version

Before updating, check the fryer's current software version on the touch screen:

Settings → Information → About This Fryer → More Information

Reminder

If the fryer is running Version 2.1.93, complete the normal software update procedure two times using the same software package to ensure the fryer is fully updated to Version 2.6.0.

08/05/2026

Download

2.1.98

Released RED compliance certification enabling global connectivity outside of South America.

04/10/2026

N/A