Applies to:

LVE 300 Software without Connectivity

NOTE: Both software and procedure applies to both General Market F5 and McDonald's LOV3.

NOTICE

Only install this software on units with no connectivity hardware (units that DO NOT have a Wi-Fi enabled dongle).

This includes:

  • All fryers manufactured with serial number: LC2602025 and before.

Installing an incompatible software version will permanently disable the control. No corrective action is available and replacing the control is required.

How to visually determine if the fryer has connectivity hardware:

HENNYLINK Label

Figure 1

Look for the HENNYLINK label, shown in figure 1, located below the power switch on the left side of the fryer. The presence of this label indicates that the fryer is equipped with connectivity hardware.

Wi-Fi Enabled Dongle

Figure 2

 

Fryers manufactured after LC2602026 include connectivity hardware. Lower the far-left control of the fryer to verify if connectivity hardware is present. Connected units include the hardware identified in red in figure 2.

If the fryer has connectivity hardware, DO NOT install this software version on your fryer.

NOTE: Connectivity field test fryers that are in the field are not compatible with this software version. These fryers that have serial numbers will have a LC2602025 and before but run on version 2.X.X. Please reach out to Henny Penny technical support if you need further assistance with replacing or updating a control on these fryers.

IMPORTANT: Do not perform this software update on F5 and LOV3 fryers which DO include connectivity. Please visit Software with Connectivity to find software updates for fryers that DO include connectivity. For assistance with which software to install, please reach out to Henny Penny technical support.

Please refer to the Software Guidance Bulletin and Memo for more information. If you need more guidance on which software to install, reach out to Henny Penny technical support.

Version Issues Fixed Date Released Click to Download
1.6.7

For both F5 OFE 51X General Market and McDonald’s LVE 300 fryers, updates have been released on Software v1.6.7 to fix some issues reported in the field.

Fixes include:

Bug Fix: Heat Recovery Logging

05/22/2026 Download
1.6.6

For both F5 OFE 51X General Market and McDonald’s LVE 300 fryers, updates have been released on Software v1.6.6 to fix some issues reported in the field.

Fixes include:

  • Bug Fix: Cook Timer did not notify user if the user was cooking in a Split Vat, 4 timer display, and in dedicated mode.

  • Quarter Cook UI Fixes

  • Resolved "Ghost Cook" on Full Vat

  • Bug Fix: Reduction of Nuisance Trips of E-21 (Heating Bug)

  • Bug Fix: Drain Valve Issues

 

New Features

  • Custom Management Password: Users can now change their management pin to 4 digits of their choice using Settings->General->Change Password.

  • Password can be reset back to default using the Fryer Resets menu Settings->Advanced->Fryer Resets.

04/08/2026 Download
1.6.4

For both F5 OFE 51X General Market and McDonald’s LVE 300 fryers, updates have been released on Software v1.6.4 to fix some issues reported in the field. Fixes include:

  • Daily Maintenance Alarm still sounding even when the setting is turned off.

  • Cook start logic failed to start with similar temp. due to C°/F° conversion issues.

  • Ukrainian translation corrections.• Quarter basket option > Dedicated mode - Removed the basket placement prompt/image to speed up the cooking process.

  • Internal software system logic updates for improved performance.

12/12/2025

N/A

Related Content

Installing the LVE 300 Open Fryer

Operating the LVE 300 Open Fryer

Training on the LVE 300 Open Fryer

Programming the LVE 300 Open Fryer

Troubleshooting the LVE 300 Open Fryer

Information about the LVE 300 Open Fryer

Selecting the Location

Unpacking

Ensuring Proper Ventilation

Electrical Requirements

Leveling the Fryer

Component Overview

Basic Operation

Purging Oil Lines

Filling or Adding Oil

Express Filter

Daily Filter

Setting Up Bulk Oil Disposal

Discarding Oil Using Front Dispose

Discarding Oil Using Rear Dispose

Discarding Oil Using Rear RTI Dispose

Discarding Oil Using Cart Dispose

Maintenance Schedule

Cleaning the Filter Pan Assembly

Replacing the Filter Pan Lid Gasket

Tighten Heat Probe and Element Spreader Bars

Deep Clean

ATO System Sequence of Operation

ATO System Theory of Operation

Bulk Oil System Sequence of Operation

Bulk Oil System Theory of Operation

Cart Dispose System Sequence of Operation

Cart Dispose System Theory of Operation

Control MAP Sequence of Operation

Control MAP Theory of Operation

Electric Heat Sequence of Operation

Electric Heat Theory of Operation

Filtering Sequence of Operation

Filtering Theory of Operation

MAP Theory of Operation

OMS Theory of Operation

PCB Theory of Operation

PMU Hi Limit Theory of Operation

Updating the Software

Factory Reset the Control

Create Food Item

Manage Food Item

Advanced Cooking Parameters

Changing from a Dedicated Display to a Multi-Product Display

Troubleshooting Guide

Troubleshooting a Blank Display

Troubleshooting an E-60 Error

Replacing the PMU Board

Unlocking Frozen Control Screen

Troubleshooting an E-10 High Limit Error

Troubleshooting an E-5 Error Oil Too Hot

Troubleshooting an E-6 Error Main or Temperature Probe

Troubleshooting an E-21 Error Recovery Fault

Troubleshooting an E-22 Error No Heat

Troubleshooting an E-31 Error Elements Up

Troubleshooting the Check JIB Message

Replacing the JIB Pump Motor

Selector Valve Port Configurations

Replacing the Selector Valve Motor

Troubleshooting Vat Overfill

Troubleshooting a Change Pad Reminder XX hrs. Error

Troubleshooting a Drain Pan Switch Failure

Troubleshooting an E-82D Selector Valve Error

Bulk Oil Retrofit Move

CE Filter Motor Cover Retrofit

Retrofitting Adjustable Filter Pan Guide Rail

Power Supply Box Louver Cover

Reference

Specifications

Error Messages

LVE 300 Plumbing Diagrams

LVE 300 Wiring Diagrams

LOV 3 Service Video Archive

LVE 300 Software with Connectivity

100 Ohm Chart