Applies to:
ALL CUSTOMERS
8 Head Baso Retrofit Kit
Required tools
1/2 in. Wrench
3/8 in. Wrench or nut driver
11/32 in. Nut driver or socket
Crosstip head screwdriver
Kit number
140095
140123
140131
140132
Estimated Time
1 to 1.5 Hours
|
To avoid electrical shock or property damage, move the power switch to OFF and disconnect power. |
-
Remove power from unit.
-
Remove control from fryer and finger-guard if present.
-
Use a 1/2 in. wrench disconnect pilot tubes from pilots.
-
Use a 3/8 in. wrench or nut driver to remove two nuts securing current pilots in place. Also disconnect ground wires and flame sense wires.
-
Locate LEFT and RIGHT pilot assemblies inside kit (marked with "L" and "R").
-
For After SN: AP0411001:
-
Place left pilot on the upper left burner bracket as shown and the right pilot on the lower left burner bracket. Secure the pilots with the four nuts provided with an 11/32” nut driver.
-
Re-attach the pilot tubes, flame sense wires and ground wires, attaching the ground wire to one of the nuts.
-
If necessary locate the female spade terminal in kit and cut and strip the spark wire on the unit and crimp the spade terminal onto spark wire. Attach spark wire to new pilot assembly.
-
Re-install the finger guard and control.
-
-
Before SN: AP04110011
-
Locate flexible pilot tubes, brass nuts & ferrules and brass T-fitting in kit. Remove SS pilot tubes and original T-fitting from unit and replace with flexible pilot tubes and T-fitting from kit.
-
Place left pilot on the upper left burner bracket as shown and the right pilot on the lower left burner bracket. Secure the pilots with the four nuts provided with an 11/32” nut driver.
-
Locate the female spade terminal in kit and cut & strip the spark wire on the unit and crimp the spade terminal onto spark wire. Attach spark wire to new pilot assembly.
-
Attach the flexible pilot tubes, flame sense wires and ground wires to new assemblies, attaching the ground wire to one of the nuts
-
Re-install the finger-guard and control.
-
Related Content
Replacing the High Temperature Limit Control
Replacing the Temperature Probe
Replacing the Gas Control Valve
Replacing the Flame Sensor Assembly
Replacing the Ignitor Assembly
Replacing the Ignition Modules
PFG-69X & OFG-39X Gas Valve Replacement Kit
Repositioning/Rewiring Air Valves for 220240V Model 690/390 fryers
Repositioning / Rewiring Air Valves for 120V Model 690/390 fryers
FM07-558 Gas Valve Replacement Kit
Manifold Retrofit Kit Instructions
PFG 690/691 Ignition Module Kit
Mounting the OFG 390 and PFG 690 Vacuum Switch
PFG 690 and 691 Temperature Probe CE Instructions
Replace Gas Valve Assembly with Gas Valve and Solenoid Assembly
Replacing Gas Valve Assembly With Gas Valve and Solenoid Assembly
Air Switch Monitoring Retrofit Kit Instructions
CE Gas Valve Adjustment Instructions
I-Beam Cable Hole Plug Installation
FM08-502 8 Head Replacing KFC Control
FM08-481 8 Head Replacing the Control
Label Application and Location for the 8 Head Fryer
PFG-690/691 & OFG-390/391 Pump Motor Relay Kit
Conversion From C8000 Control to KFC SMS Control
Rear Cover Removal Instructions
Replace Nylatron Slides on PFG 690 and 691
Installing Optional Crumb Basket
PFG 690 and 691 Installing Filter Rinse Hose
PFG 690 Stabilizer Retrofit Instructions
Conversion From Standard 690 Control to S/M Control
PFG 691 C8000 Retrofit Instructions
PFG 690 and 691 Lid Cable Replacement
Operating Instructions for PFG-691/OFG-391 Direct-Connect Oil System
Direct-Connect Retrofit Instructions (For use on fryers after SN: 391-LH016JC & 691-LH029JC)
Replacing the High Temperature Limit Control
Replacing the Temperature Probe
Replacing the Gas Control Valve
Replacing the Flame Sensor Assembly
Replacing the Ignition Modules
Replacing the Ignitor Assembly
PFG 691 Attaching the Rinse Hose Instructions
Reference
PFG 690 and 692 Inspection and Planned Maintenance
